Peugeot 405

1987-1997 of release

Repair and operation of the car

Peugeot 405
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Fuel system
+ 5. Lubrication systems, coolings
+ 6. System of release
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Steering
+ 11. Suspension brackets
+ 12. Brake system
- 13. Body
   13.1. Care of a body
   13.2. Care of an upholstery and rugs
   13.3. Repair of insignificant damages of a body
   13.4. Repair of strong damages of a body
   13.5. Front bumper
   13.6. Rear bumper
   13.7. Replacement of a headlight and index of turns
   13.8. Replacement of a back lamp
   13.9. Replacement of a forward wing
   13:10. Cowl
   13:11. Cowl lock cable
   13:12. Cowl lock
   13:13. Replacement of the forward panel
   13:14. Doors
   13:15. Door upholstery
   13:16. Lock and handles of opening of a door
   13:17. Glasses of doors
   13:18. Trunk lid (Sedan models)
   13:19. Lock of a trunk lid (Sedan model)
   13:20. Back door (model of Kombi)
   13:21. Lock of a back door (model of Kombi)
   13:22. Central blocking
   13:23. Power windows
   13:24. External rear-view mirrors
   13:25. Front and back flew down
   13:26. Hatch
   13:27. Removable elements of a body
   13:28. Seats
   13:29. Seat belts
   13:30. Finishing of salon
   13:31. Ceiling upholstery
   13:32. Central console
   13:33. Dashboard
+ 14. Electric equipment

13:15. Door upholstery

GENERAL INFORMATION

Prevention

The upholstery of a door can have changes depending on the level of finishing of salon. Therefore process of removal of an upholstery can differ from stated.

The actions connected with removal of an upholstery of forward and back doors are identical.

Removal

PERFORMANCE ORDER

1. To lower glass of a door it is more, than half.
	2. By means of the screw-driver (for extraction of a special ledge) to remove an overlay of the door handle.
	3. In the cars equipped with the built-in loudspeakers to unscrew screws of a lattice of the loudspeaker or to remove fastening brackets, to disconnect, and then to take a loudspeaker.
	4. To remove the button of draft of blocking of doors for what to pull it up, at the same time the screw-driver wringing out a clamp.
5. On models with a manual window regulator to remove its handle about axes and laying.
	6. In versions with electrically the lifted glasses to switch-off the accumulator, then by means of the screw-driver to take the switch from a door and to disconnect the socket.
	7. To remove a decorative overlay of an external mirror.
	8. To unscrew three screws of fastening of an armrest and to remove an armrest.
	9. On later models by means of the lever to remove a finishing plate from a back part of a pocket of a door and to unscrew the screw of fastening of a back part of an upholstery of doors.
10. Where it is applicable, using the screw-driver, to disconnect the brackets of fastening of an upholstery located in a nest for a loudspeaker.
11. By means of flat special adaptation in the form of forks to unhook a door upholstery so that not to damage plastic latches. In case of damage of latches it is not necessary to stick together them, and to establish in internal strengthening of an upholstery of a door.
12. To raise an upholstery and to remove it from a door.

Installation

PERFORMANCE ORDER

1. On openings of a framework of a door to paste a plastic tape to protect from corrosion and that water did not get in salon.
2. To establish all latches in the corresponding openings of a door and to fix a door upholstery.

3. To install the button of draft of blocking of doors for what to arrange draft in lower of two openings, to strongly pull the button over draft before fixing, at the same time draft of fastening will appear in the top opening.
4. To perform other operations in the return sequence in relation to removal of an upholstery.
5. During the movement to check whether vibration of an upholstery of a door appears.
Prevention For protection of doors from corrosion and also to achieve a deaf sound at their closing, it is necessary to fill in special bituminous means in an internal cavity of a door. It can be made only when a framework of a door ideally dry (without the slightest traces of moisture).

On the homepage