Peugeot 405

1987-1997 of release

Repair and operation of the car



Peugeot 405
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Fuel system
+ 5. Lubrication systems, coolings
+ 6. System of release
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Steering
+ 11. Suspension brackets
+ 12. Brake system
+ 13. Body
- 14. Electric equipment
   14.1. Technical characteristic
   14.2. Detection of not closed chain
   14.3. Generator
   14.4. Starter
   14.5. Replacement of switches
   14.6. Other electric devices
   14.7. Bulbs of external lighting
   14.8. Bulbs of internal lighting
   14.9. External lighting fixtures
   14:10. Adjustment of light of headlights
   14:11. Combination of devices
   14:12. Elements of a combination of devices
   14:13. Hours
   14:14. Screen wiper levers
   14:15. Engine of a screen wiper and draft
   14:16. Engine of a screen wiper of a back door
   14:17. Windscreen washers
   14:18. Radio receiver
   14:19. Loudspeakers
   14:20. Antenna
   14:21. Anticreeping system
   14:22. Safety cushion
   14:23. Safety cushion elements
   14:24. System of heating and ventilation
   + 14:25. Electrical circuitries and charts


e1bd1949



14:23. Safety cushion elements

GENERAL INFORMATION

Safety cushion sensors compound with the electronic control device which is independently compound with a steering wheel. A lamp of the alarm system of a safety cushion compound with safety cushion unit.

ELECTRONIC CONTROL DEVICE OF THE SAFETY CUSHION

The electronic control device of a safety cushion compound with a steering wheel can be also removed only with a steering wheel.

SAFETY CUSHION

Safety cushion – an integral part of a steering wheel.

Removal

PERFORMANCE ORDER
1. Before performance of any actions on a security system to remove the negative plug from the accumulator and to wait, at least, 10 minutes.
2. To unscrew two screws (are specified by shooters) the fastenings of a safety cushion located from a back part of a steering wheel. For access to screws to turn a steering wheel.
3. To disconnect the electric socket from a safety cushion.

Installation

PERFORMANCE ORDER
1. Installation is made in the sequence, the return to removal. At the same time it is necessary to consider the next moments.
2. Not to strike a safety cushion or to subject to collisions in the course of installation on the former place.
3. To tighten screws of fastening of a safety cushion the required moment.
4. In conclusion to make active system of a safety cushion for what to perform the following operations.
5. To close car doors, at the same time in the car there should not be people.
6. To include ignition.
7. To connect a weight wire to the accumulator.
8. To switch off ignition.
9. To repeatedly include ignition and to check that the lamp of the alarm system of a safety cushion on a steering wheel burns three seconds then dies away.
10. To include ignition.

ROTARY CONNECTOR OF THE SAFETY CUSHION

Rotary connector of a safety cushion

1 – rotary connector,

2 – electric socket,

3 – brackets of fastening of a rotary connector


Removal

PERFORMANCE ORDER
1. To remove a safety cushion.
2. To remove a steering wheel.
3. To unscrew screws of fastening and to remove the lower casing of a steering column.
4. To remove the top casing of a steering column.
5. To disconnect the electric socket from a rotary connector.
6. Using the screw-driver, to release three brackets of fastening and to remove a rotary connector.

Installation

PERFORMANCE ORDER
1. Installation is made in the sequence, the return to removal. At the same time it is necessary to consider the next moments.
2. Before installation to check for the former place of casings of a steering column and safety cushion that the plait of wires was laid correctly and, moving a steering wheel that the electrical wiring does not cling to anything.
3. To establish a steering wheel.
4. To establish a safety cushion, but not to make active a safety cushion at this stage.
5. In conclusion to move a steering column to the lifted situation, then to check that the gap between a back part of a steering wheel and casings of a steering column was 8,0 mm. If the gap differs from demanded, to perform the following operations.
6. To turn off a carpet about pedals for access to a coupling bolt of a steering column.
7. To weaken a coupling bolt and to move a steering shaft before receiving a gap between a back part of a steering wheel and casings of a steering column of equal 8,0 mm.
8. To tighten a coupling bolt and to establish into place a carpet.
9. To make active a safety cushion.

On the homepage