Peugeot 405 + 1. Maintenance instruction + 2. Maintenance + 3. Engines + 4. Fuel system + 5. Lubrication systems, coolings + 6. System of release + 7. Coupling + 8. Transmissions + 9. Power shafts + 10. Steering + 11. Suspension brackets + 12. Brake system + 13. Body - 14. Electric equipment 14.1. Technical characteristic 14.2. Detection of not closed chain 14.3. Generator 14.4. Starter 14.5. Replacement of switches 14.6. Other electric devices 14.7. Bulbs of external lighting 14.8. Bulbs of internal lighting 14.9. External lighting fixtures 14:10. Adjustment of light of headlights 14:11. Combination of devices 14:12. Elements of a combination of devices 14:13. Hours 14:14. Screen wiper levers 14:15. Engine of a screen wiper and draft 14:16. Engine of a screen wiper of a back door 14:17. Windscreen washers 14:18. Radio receiver 14:19. Loudspeakers 14:20. Antenna 14:21. Anticreeping system 14:22. Safety cushion 14:23. Safety cushion elements 14:24. System of heating and ventilation + 14:25. Electrical circuitries and charts
|
Prevention
To disconnect a negative wire from the accumulator before removal of any lighting fixture and to repeatedly connect a negative wire to the accumulator after installation of the lighting fixture.
HEADLIGHT
Prevention
Before removal of optical knots of headlights it is necessary to designate on a wall (for example, in an underground garage) a light trace from headlights of near and far light, and also the provision of all four wheels.
Removal
PERFORMANCE ORDER |
1. Working in a motor compartment, to release a bracket, the fixing cover to a back part of a headlight. |
2. To disconnect wires from the glow lamps located in a headlight. |
3. Working in a motor compartment, to disconnect the fixing spring of a lamp of the forward index of turn from a ledge. |
4. To take the forward index of turns from a wing. |
5. On models with the proofreader of light of headlights to disconnect the proofreader from a headlight as follows. |
6. To take the proofreader's case from a suspension bracket on the forward panel. |
|
7. To take spherical hinged connection from a nest in a back part of a headlight. |
8. On models with electrically the operated proofreader of light of headlights to disconnect wires from the proofreader in a back part of a headlight. |
9. To remove a front grille. |
|
10. To unhook the level located under a headlight, paying attention not to damage fastening about a wing edge. |
|
11. To unscrew two (are specified by an arrow) external a bolt of fastening of a headlight and to take a headlight forward from the body panel. |
|
12. To remove metal clips of fastening of glass to a headlight and to remove glass from a headlight. |
13. Before installation of glass of a headlight to check that the consolidation located in a flute on headlight perimeter in good shape. |
|
Installation
PERFORMANCE ORDER |
1. Installation is made in the sequence, the return to removal. |
2. As soon as possible to adjust light of headlights. |
|
FORWARD INDEX OF TURN
PERFORMANCE ORDER |
1. Working in a motor compartment, to disconnect the fixing spring of a lamp of the forward index of turn from a ledge. |
2. To take the forward index of turns from a wing. |
|
FORWARD SIDE REPEATER OF TURNS
PERFORMANCE ORDER |
To turn the forward side repeater of turns counterclockwise and to take it from a car wing. |
|
FORWARD FOG LIGHTS
Two types of headlights can be established. Headlights can be established or directly in a forward spoiler, or in the nest screwed on a forward spoiler.
PERFORMANCE ORDER |
The fog light established in a spoiler nest |
1. In a back part of a spoiler to disconnect the electric socket from a headlight. |
|
2. To unscrew two screws (are specified by an arrow) fastenings of a fog light to a spoiler, then to take a headlight with a nest from a spoiler. |
|
3. To unscrew a nut (it is specified by an arrow) fastenings in a back part of a headlight and to take a headlight from a nest. |
4. Installation is made in the sequence, the return to removal. |
5. To check and if it is necessary, to adjust light of headlights, using nuts with a nakatka in a back part of a headlight. |
Headlight established directly in a spoiler |
Prevention
Some models are equipped with forward fog lights which have no the screws of fastening seen from headlight glass.
|
6. To lift a forward part of the car and to record on supports. |
7. To track an electrical wiring back from a fog light and to disconnect the electric socket. |
8. To unscrew nuts of fastening and to take a headlight from a spoiler. |
9. Installation is made in the sequence, the return to removal. |
|
BACK LAMP (MODELS SEDAN)
PERFORMANCE ORDER |
1. To open a trunk lid. |
2. To squeeze two brackets of fastening and to take the holder of bulbs from a back lamp. |
3. To disconnect the electric socket from the holder of bulbs. |
4. To remove finishing of the luggage compartment. |
|
5. To unscrew nuts (are specified by shooters) fastenings of a back lamp. |
|
6. To remove a back lamp, at the same time it is necessary to take an external part of a lamp at first. |
7. Installation is made in the sequence, the return to removal. |
|
BACK LAMP (KOMB MODELS)
Fires of a stoplight and the index of turn are located in a back wing. Other bulbs of a back lamp are located in a back door.
PERFORMANCE ORDER |
1. To open a back door. |
2. To turn a bracket of fastening and to open a folding shutter of a covering of the luggage compartment. |
3. To squeeze two brackets of fastening and to take the holder of bulbs from a back lamp. |
4. To disconnect the electric socket from the holder of bulbs. |
|
5. To unscrew nuts (are specified by shooters) fastenings of a back lamp. |
|
6. To unscrew nuts (are specified by shooters) fastenings of a back lamp to a door. |
|
7. To remove a back lamp. |
8. Installation is made in the sequence, the return to removal. |
|
ILLUMINATION OF REGISTRATION PLATE (MODEL SEDAN)
PERFORMANCE ORDER |
|
1. To unscrew two screws (are specified by shooters) fastenings, then to take an illumination lamp from a bumper and to disconnect the electric socket. |
2. Installation is made in the sequence, the return to removal. |
|
ILLUMINATION OF REGISTRATION PLATE (KOMB MODEL)
PERFORMANCE ORDER |
1. By means of the lever to remove a lamp of illumination of registration plate from a back door and to disconnect the electric socket. |
2. Installation is made in the sequence, the return to removal. |
|
|
On the homepage
|