Peugeot 405

1987-1997 of release

Repair and operation of the car



Peugeot 405
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
   - 3.1. Petrol engines
      3.1.1. Technical characteristic
      - 3.1.2. Repair of the engine
         + 3.1.2.1. The repair which is not demanding removal of the engine
         + 3.1.2.2. Removal of the engine
         3.1.2.3. Installation of the engine
         3.1.2.4. Dismantling of the engine
         + 3.1.2.5. Assembly of the engine
         3.1.2.6. Start of the engine after capital repairs
   + 3.2. Diesel engines
   + 3.3. Petrol engine 1,4 of dm3
   + 3.4. System of ignition
+ 4. Fuel system
+ 5. Lubrication systems, coolings
+ 6. System of release
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Steering
+ 11. Suspension brackets
+ 12. Brake system
+ 13. Body
+ 14. Electric equipment


e1bd1949



3.1.2.3. Installation of the engine

GENERAL INFORMATION

Prevention

It is recommended to replace systematically sealing rings of differential and самоконтрящиеся nuts which were removed.


PERFORMANCE ORDER
1. To install the engine in a motor compartment.
2. To establish on the left side an elastic support of a suspension bracket of the transmission and to tighten two nuts the moment of 17,5 Nanometers.
3. To tighten the central nut the moment of 35 Nanometers.
4. To establish the right arm of an engine mount and to tighten nuts the moment of 45 Nanometers.
5. To install in the cars equipped with the hydraulic booster of system of steering:
      – belt tension level;
      – pulley of the pump of the hydraulic booster;
      – pipelines of the pump of the hydraulic booster.
6. To establish and pull a belt.
7. To establish a radiator.
8. To connect elements of the mechanism of gear shifting and a cable of an otblokirovka of the reverse gear.
9. To establish and adjust a coupling cable.
10. To connect earlier turned off electric connections.
11. To connect pipelines of the cooling system, the vacuum amplifier of brakes and fuel-supply lines.
12. To establish an accelerator cable, knot of the air filter, the accumulator (without connecting it) and its arm.
13. To connect a speedometer cable.
14. To establish a reception pipe.
15. To grease edges of a sealing ring and to establish the right half shaft in differential.
16. To install the intermediate bearing case and to tighten bolts the moment of 25 Nanometers (at first having greased them with means of Loctite Frenetanch).
17. To turn bolts of fastening of the bearing half way and to tighten nuts the moment of 17,5 Nanometers.
18. To establish an arm of connection of the engine with a body.
19. A nut from the engine to tighten the moment 35 Nanometers, and a nut from a body the moment of 45 Nanometers.
20. To take a plastic casing of the right sealing ring.
21. To establish the left half shaft in differential.
22. To connect a rotary fist to levers and to tighten nuts the moment of 30 Nanometers.
23. To establish a plastic casing of the transmission.
24. To remove a casing of a sealing ring.
25. To establish wheels. To lower the car on wheels.
26. To establish connectors of the stabilizer and to tighten bolts the moment of 65 Nanometers.
27. To fill in oil in the engine and in the transmission.
28. To fill in cooling liquid and to remove air from the cooling system.
29. To fill in oil in a contour of the hydraulic booster of system of steering and to remove air from a contour (in the cars equipped with the hydraulic booster of system of steering).

On the homepage