Peugeot 405
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Fuel system
+ 5. Lubrication systems, coolings
+ 6. System of release
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Steering
+ 11. Suspension brackets
+ 12. Brake system
+ 13. Body
- 14. Electric equipment
14.1. Technical characteristic
14.2. Detection of not closed chain
14.3. Generator
14.4. Starter
14.5. Replacement of switches
14.6. Other electric devices
14.7. Bulbs of external lighting
14.8. Bulbs of internal lighting
14.9. External lighting fixtures
14:10. Adjustment of light of headlights
14:11. Combination of devices
14:12. Elements of a combination of devices
14:13. Hours
14:14. Screen wiper levers
14:15. Engine of a screen wiper and draft
14:16. Engine of a screen wiper of a back door
14:17. Windscreen washers
14:18. Radio receiver
14:19. Loudspeakers
14:20. Antenna
14:21. Anticreeping system
14:22. Safety cushion
14:23. Safety cushion elements
14:24. System of heating and ventilation
+ 14:25. Electrical circuitries and charts
|
Prevention
Before replacement of bulbs of external lighting to check the corresponding electric chain and a safety lock.
Do not touch a glass flask of a lamp by hands. The fingerprint evaporates and besieged on a reflector therefore lighting worsens. It is obligatory to replace the failed lamps with lamps of the same type. To wipe the spots arising on imprudence from a touch with a pure lint-free rag or alcohol.
HEADLIGHT
| PERFORMANCE ORDER |
|
1. To release brackets (are specified by an arrow) fastenings and to uncover a back part of a headlight. |
| 2. To remove the electric socket from a back part of the glow lamp of a headlight. |
|
3. To squeeze spring brackets (are specified by an arrow) fastenings of a bulb and to cast away them aside. |
|
4. To take a bulb from a headlight. |
| 5. To establish a new bulb so that ledges on the boss of a bulb were combined with headlight grooves, and to fix a bulb by spring brackets. |
| 6. To connect the electric socket and to establish a back cover of a headlight. |
|
FORWARD DIMENSIONAL LAMP
The glow lamp of a dimensional lamp is located in a back part of a headlight.
| PERFORMANCE ORDER |
| 1. To release a bracket of fastening and to remove a back cover from a headlight. |
|
2. On models till 1992 to take the boss with a bulb from a back part of a headlight. On models since 1993 to turn the boss with a bulb on a quarter of a turn and to take a cartridge with a bulb from a back part of a headlight. |
|
3. To take the glow lamp from the boss, having just pulled it on itself. |
| 4. Installation is made in the sequence, the return to removal. |
|
FORWARD INDEX OF TURN
| PERFORMANCE ORDER |
|
1. Working in a motor compartment, to disconnect the fixing spring (it is specified by an arrow) lamps of the forward index of turn from a ledge. |
| 2. To take the forward index of turns from a wing. |
|
3. To turn a cartridge counterclockwise to take it from the forward index of turns. |
| 4. To take the glow lamp from the boss, having just pulled it on itself. |
| 5. Installation is made in the sequence, the return to removal, at the same time to check that the fixing spring is correctly established. |
|
FORWARD SIDE REPEATER OF TURNS
| PERFORMANCE ORDER |
| 1. To turn the forward side repeater of turns counterclockwise and to take it from a car wing. |
| 2. To turn a cartridge with a bulb counterclockwise and to take it from the forward side repeater of turns. |
|
3. To take the glow lamp from the boss, having just pulled it on itself. |
| 4. Installation is made in the sequence, the return to removal. |
|
ADDITIONAL FORWARD LIGHT
On some models additional forward light is established in a headlight. The additional forward light is turned on at inclusion of driving beam. Replacement of a bulb is made as well as bulbs of a headlight (see above).
| PERFORMANCE ORDER |
|
1. To release spring brackets (are specified by an arrow) fastenings of a bulb of additional forward light. |
|
2. To take a bulb of additional forward light from a headlight. |
|
FORWARD FOG LIGHTS
Prevention
Some models are equipped with forward fog lights which have no the screws of fastening seen from headlight glass.
Two types of headlights can be established. On some models access to the glow lamp can be possible from a back part of a spoiler. On other models for access to a bulb it is necessary to remove a headlight.
| PERFORMANCE ORDER |
| 1. On models where access to the glow lamp is possible from a back part of a spoiler to disconnect the electric socket from a bulb. |
| 2. To remove a rubber cover from a headlight, then to squeeze spring clamps and to take a bulb. |
| 3. On models where a back part of a fog light is closed by a spoiler to unscrew two screws of fastening from a forward part of a headlight and to take a headlight from a spoiler. |
| 4. To disconnect the electric socket from a bulb, then to squeeze spring clamps and to take a bulb. |
|
BACK LAMP (MODELS SEDAN)
| PERFORMANCE ORDER |
| 1. To open a trunk lid. |
|
2. To squeeze two brackets of fastening and to take the holder of bulbs from a back lamp. |
|
3. For extraction of a bulb to press it, in this situation to turn in any party and to take from the holder. |
| 4. Installation is made in the sequence, the return to removal. |
|
BACK LAMP (KOMB MODELS)
Fires of a stoplight and the index of turn are located in a back wing. Other bulbs of a back lamp are located in a back door.
| PERFORMANCE ORDER |
| 1. To open a back door. |
| 2. To turn a bracket of fastening and to open a folding shutter of a covering of the luggage compartment. |
|
3. To squeeze two brackets of fastening and to take the holder of bulbs from a back lamp. |
|
4. For extraction of a bulb to press it, in this situation to turn in any party and to take from the holder. |
| 5. Installation is made in the sequence, the return to removal. |
|
ILLUMINATION OF REGISTRATION PLATE (MODEL SEDAN)
| PERFORMANCE ORDER |
|
1. Using the thin screw-driver, to remove a plafond from a reverse side of a bumper for access to the glow lamp. |
|
2. For extraction of a bulb to press it, in this situation to turn in any party and to take from the holder. |
| 3. Installation is made in the sequence, the return to removal. |
|
ILLUMINATION OF REGISTRATION PLATE (KOMB MODEL)
| PERFORMANCE ORDER |
|
1. Using the thin screw-driver, to remove a lamp of illumination of registration plate from a back door. |
|
2. To take a cartridge with a bulb from a lamp. |
| 3. For extraction of a bulb to press it, in this situation to turn in any party and to take from the holder. |
| 4. Installation is made in the sequence, the return to removal. |
|
|
On the homepage
|
