Peugeot 405

1987-1997 of release

Repair and operation of the car



Peugeot 405
+ 1. Maintenance instruction
- 2. Maintenance
   2.1. Technical characteristic
   + 2.2. Frequency of service
   + 2.3. Each 7 500 km
   + 2.4. Each 10 000 km or 6 months
   - 2.5. Each 20 000 km or 12 months
      2.5.1. Control of hoses of system of ventilation of a case of the engine
      2.5.2. Replacement of the fuel filter
      2.5.3. Check of turns of idling and composition of mix (SO)
      2.5.4. Replacement of spark plugs
      2.5.5. Check, adjustment and lubricant of coupling
      2.5.6. Check of a condition of a protective cover of a power shaft
      2.5.7. Check of a condition of lobbies and back brake shoes
      2.5.8. Check and adjustment of the emergency brake
      2.5.9. Check of a condition of a suspension bracket
      2.5.10. Check of drainage openings
   + 2.6. Each 30 000 km or 18 months
   + 2.7. Each 40 000 km or 2 years
   + 2.8. Each 60 000 km or 3 years
+ 3. Engines
+ 4. Fuel system
+ 5. Lubrication systems, coolings
+ 6. System of release
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Steering
+ 11. Suspension brackets
+ 12. Brake system
+ 13. Body
+ 14. Electric equipment


e1bd1949



2.5.3. Check of turns of idling and composition of mix (SO)

GENERAL INFORMATION

Point of adjustment of turns of idling on models with the compensator of turns of idling

The point of adjustment of turns of idling is specified by an arrow.

Prevention

On models since 1994 the specified interval for this procedure – 30 000 km.


Before check of turns of idling and composition of mix it is necessary to check:

 – installation of a corner of an advancing of ignition;
 – condition of spark plugs;
 – an accelerator cable (on carburetor models – also a cable of the drive of a butterfly valve);
 – hoses of system of ventilation of a case;
 – the filtering element of the air filter;
 – system of production of exhaust gases;
 – compression and gap of valves.

PERFORMANCE ORDER
1. To warm up the engine up to the normal working temperature and to make adjustment within 2 minutes, without stopping the engine.
2. If joins the electric fan of cooling of a radiator, adjustment to make only after its switching off.
Models with the carburetor
3. All electric consumers have to be switched off, the air gate is completely open.
4. If the car has no tachometer, to connect a tachometer according to the instruction.
5. To check turns of idling and to compare them to the data provided in subsection 3.1.1 (in subsection 3.3.1 for dm3 engines 1,4).

Prevention

Models with air conditioning have the device of compensation of the mode of idling.


6. Using the corresponding screw-driver, screw in the adjusting screw (to increase speed) or unscrew as required that turns of idling of the engine met standard.
7. Adjustment of contents WITH in exhaust gases is executed at manufacturer, no further adjustment is required. However after capital repairs of the carburetor repeated adjustment can be made.
8. Adjustment of contents WITH in exhaust gases can be made only at Peugeot car repair shops.
9. The screw of adjustment of turns of idling is closed by a stopper to prevent casual adjustment. For access to the screw it is necessary to take the sharp tool a stopper.
10. The screw-driver to turn the screw (it is specified by an arrow) mix regulations very slowly, the required SO level will not be established yet. Screwing up of the screw clockwise reduces contents WITH and vice versa, unscrewing of the screw counterclockwise increases contents WITH.
11. After adjustment of contents WITH to establish a new stopper cap and if necessary to adjust idling turns.
Models with system of injection of fuel. System of injection of Bosch L fuel. 3. l-Jetronic
12. All electric consumers have to be switched off.
13. If the car has no tachometer, to connect a tachometer according to the instruction.
14. To check turns of idling and to compare them to the data provided in subsection 3.1.1.
15. Regulation of turns of idling is made, screwing in the screw in the case of throttles. The turn of the screw clockwise reduces idling turns.
16. Adjustment of contents WITH in exhaust gases can be made only at Peugeot car repair shops.
17. The screw of adjustment of turns of idling is located on the measuring instrument of a stream of air and closed by a stopper to prevent casual adjustment. For access to the screw it is necessary to take the sharp tool a stopper. The screw-driver to turn the screw (it is specified by an arrow) mix regulations very slowly, the required SO level will not be established yet.
System of injection of Bosch ML4 fuel. l Motronic
18. Turns of idling are not regulated, and are run by the valve of the regulator of turns of idling.
19. Adjustment of contents WITH in exhaust gases can be made only at Peugeot car repair shops.
20. The screw of adjustment of turns of idling is located on the measuring instrument of a stream of air and closed by a stopper to prevent casual adjustment.
21. Turning the screw (it is specified by a sterlka) clockwise, increase contents WITH and vice versa, rotating the screw counterclockwise, reduce the SO level.
System of injection of Bosch LU2-JETRONIC fuel
22. Contents WITH in exhaust gases is automatically regulated by the ECU block.
23. Turns of idling are regulated by the screw (2).
System of injection of Bosch Motronic MP3 fuel. L
24. All electric consumers have to be switched off.
25. If the car has no tachometer, to connect a tachometer according to the instruction.
26. Turns of idling are regulated by the screw (1).
27. Adjustment of contents WITH in exhaust gases can be made only at Peugeot car repair shops.
28. The screw of adjustment of turns of idling is located on the measuring instrument of a stream of air and closed by a stopper to prevent casual adjustment.
29. Turning the screw (2) clockwise, increase contents WITH and vice versa, rotating the screw counterclockwise, reduce the SO level.
System of injection of Bosch Motronic MI fuel. 3
30. Turns of idling are regulated only on the XU9JA/Z engine – on other engines management is made by the adjusting valve of turns of idling and the ECU block.
31. All electric consumers have to be switched off.
32. If the car has no tachometer, to connect a tachometer according to the instruction.
33. To check turns of idling and to compare them to the data provided in subsection 3.1.1. Turns of idling are regulated by the screw (7).
34. Adjustment of contents WITH can be made only on the XU9J4/K engine, on other engines adjustment is made by the ECU block.
35. Adjustment of contents WITH in exhaust gases can be made only at Peugeot car repair shops.
36. The screw of adjustment of contents WITH is located from above on the measuring instrument of a stream of air and closed by a stopper to prevent casual adjustment.
37. Turning the screw (5) clockwise, increase contents WITH and vice versa, rotating the screw counterclockwise, reduce the SO level.
System Magneti Marelli engine management

38. On models with system Magneti Marelli engine management adjustment of composition of mix is possible only reprogramming of the ECU block with use of the special electronic test equipment.


On the homepage