Peugeot 405 + 1. Maintenance instruction + 2. Maintenance + 3. Engines + 4. Fuel system + 5. Lubrication systems, coolings + 6. System of release + 7. Coupling + 8. Transmissions + 9. Power shafts - 10. Steering 10.1. Technical characteristic 10.2. Steering wheel 10.3. Steering column 10.4. Ignition lock 10.5. Steering transfer 10.6. Replacement of protective covers of the steering mechanism 10.7. Removal of air from system of steering with the amplifier 10.8. Pump of the amplifier of steering 10.9. Check of level of oil in system of steering with the hydraulic booster 10:10. Tip of steering draft 10:11. Steering draft 10:12. Angles of installation of wheels 10:13. Changes in system of steering + 11. Suspension brackets + 12. Brake system + 13. Body + 14. Electric equipment
|
MODELS WITH XU5 AND XU9 ENGINES (EXCEPT XU9J4)
Removal
PERFORMANCE ORDER |
1. To remove a weight wire from the accumulator. |
2. On models with the steering drive with the hydraulic booster to merge liquid from a hydraulic system as follows: – to uncover a nutritious tank; – to place a container under the coupling of the pipeline of high pressure on steering transfer, then to unscrew connection; – to merge liquid in a container; – to finish discharge of oil from a contour, turning several times a steering wheel in both directions against the stop; – to disconnect a hose of low pressure from steering transfer. |
|
3. To record a pump shaft from a provorachivaniye and to weaken bolts of fastening of a pulley. |
4. To weaken a bolt of a natyazhitel of a belt of the generator and to take off a driving belt of the pump. |
5. To reject the generator up, to tighten a bolt of fastening of a natyazhitel. |
6. To unscrew bolts of fastening of a pulley of the pump and to remove a pulley. |
7. To disconnect the pipeline of supply of oil to the pump. |
8. To weaken a collar of fastening of a hose and to disconnect a hose from the pump. If the collar of fastening of a hose has tightening type, to throw out it and to establish a new collar with the screw. |
|
9. To unscrew two lobbies and two back bolts of fastening of the pump. |
|
10. To remove the pump of the amplifier of steering. |
|
The pump is not under repair and with defects is subject to replacement.
Installation
PERFORMANCE ORDER |
Installation is made in the sequence of the return to removal taking into account the next moments: – to tighten all bolts the required moment; – to adjust a tension of a driving belt; – to add liquid in system of steering. |
|
MODELS WITH XU9J4 ENGINES
Removal
PERFORMANCE ORDER |
1. To remove a weight wire from the accumulator. |
2. On models with the steering drive with the hydraulic booster to merge liquid from a hydraulic system as follows: – to uncover a nutritious tank; – to place a container under the coupling of the pipeline of high pressure on steering transfer, then to unscrew connection; – to merge liquid in a container; – to finish discharge of oil from a contour, turning several times a steering wheel in both directions against the stop; – to disconnect a hose of low pressure from steering transfer. |
3. To take off a driving belt of the pump. |
4. To unscrew the coupling of the pipeline and to disconnect a pipe from the pump. |
5. To weaken a collar of fastening of a hose and to disconnect a hose from the pump. If the collar of fastening of a hose has tightening type, to throw out it and to establish a new collar with the screw. |
6. To unscrew bolts of fastening of the pump and to remove the pump. |
|
The pump is not under repair and with defects is subject to replacement.
Installation
PERFORMANCE ORDER |
Installation is made in the sequence of the return to removal taking into account the next moments: – to tighten all bolts the required moment; – to adjust a tension of a driving belt; – to add liquid in system of steering. |
|
MODELS WITH XU7 AND XU10 ENGINES WITHOUT AIR CONDITIONING
Arrangement of two forward bolts of fastening of the pump of the amplifier of steering
Arrangement of a back bolt of fastening of the pump of the amplifier of steering
Removal
PERFORMANCE ORDER |
1. To remove a weight wire from the accumulator. |
2. On models with the steering drive with the hydraulic booster to merge liquid from a hydraulic system as follows: – to uncover a nutritious tank; – to place a container under the coupling of the pipeline of high pressure on steering transfer, then to unscrew connection; – to merge liquid in a container; – to finish discharge of oil from a contour, turning several times a steering wheel in both directions against the stop; – to disconnect a hose of low pressure from steering transfer. |
3. To lift a forward part of the car and to record on supports. To remove a forward right wheel. |
4. To take off a driving belt of the pump. |
5. To unscrew the pipeline coupling and to disconnect a pipe from the pump. |
6. To weaken a collar of fastening of a hose and to disconnect a hose from the pump. If the collar of fastening of a hose has tightening type, to throw out it and to establish a new collar with the screw. |
7. To unscrew two forward bolts of fastening of the pump, access to which is possible through openings in a pump pulley (see rice. Arrangement of two forward bolts of fastening of the pump of the amplifier of steering). |
8. To unscrew a back bolt of the pump of fastening and to remove the pump from the engine (see rice. Arrangement of a back bolt of fastening of the pump of the amplifier of steering). |
|
Installation
PERFORMANCE ORDER |
Installation is made in the sequence of the return to removal taking into account the next moments: – to tighten all bolts the required moment; – to adjust a tension of a driving belt; – to add liquid in system of steering. |
|
MODELS WITH XU7 AND XU10 ENGINES WITH AIR CONDITIONING
Arrangement of a bolt of fastening of a suspension bracket of installation of the pump to the generator of alternating current
Arrangement of a back bolt of fastening of the pump
Removal
PERFORMANCE ORDER |
1. On models with the steering drive with the hydraulic booster to merge liquid from a hydraulic system as follows: – to uncover a nutritious tank; – to place a container under the coupling of the pipeline of high pressure on steering transfer, then to unscrew connection; – to merge liquid in a container; – to finish discharge of oil from a contour, turning several times a steering wheel in both directions against the stop; – to disconnect a hose of low pressure from steering transfer. |
2. To unscrew the pipeline coupling and to disconnect a pipe from the pump. |
3. To weaken a collar of fastening of a hose and to disconnect a hose from the pump. If the collar of fastening of a hose has tightening type, to throw out it and to establish a new collar with the screw. |
4. To unscrew two forward bolts of fastening of the pump, access to which is possible through openings in a pump pulley. |
5. To unscrew the bolt fixing a suspension bracket of installation of the pump to the generator of alternating current (see rice. An arrangement of a bolt of fastening of a suspension bracket of installation of the pump to the generator of alternating current). |
6. To unscrew a back bolt of fastening of the pump and to remove the pump from the engine (see rice. Arrangement of a back bolt of fastening of the pump). |
|
Installation
PERFORMANCE ORDER |
Installation is made in the sequence of the return to removal taking into account the next moments: – to tighten all bolts the required moment; – to adjust a tension of a driving belt; – to add liquid in system of steering. |
|
|
On the homepage
|