Peugeot 405
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Fuel system
+ 5. Lubrication systems, coolings
+ 6. System of release
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Steering
+ 11. Suspension brackets
+ 12. Brake system
+ 13. Body
- 14. Electric equipment
14.1. Technical characteristic
14.2. Detection of not closed chain
14.3. Generator
14.4. Starter
14.5. Replacement of switches
14.6. Other electric devices
14.7. Bulbs of external lighting
14.8. Bulbs of internal lighting
14.9. External lighting fixtures
14:10. Adjustment of light of headlights
14:11. Combination of devices
14:12. Elements of a combination of devices
14:13. Hours
14:14. Screen wiper levers
14:15. Engine of a screen wiper and draft
14:16. Engine of a screen wiper of a back door
14:17. Windscreen washers
14:18. Radio receiver
14:19. Loudspeakers
14:20. Antenna
14:21. Anticreeping system
14:22. Safety cushion
14:23. Safety cushion elements
14:24. System of heating and ventilation
+ 14:25. Electrical circuitries and charts
|
THE ANTENNA INSTALLED ON THE ROOF
The antenna can be just unscrewed from the basis. For removal of the antenna in a set it is necessary to perform the following operations.
| PERFORMANCE ORDER |
| 1. To disconnect a negative wire from the accumulator. |
| 2. To remove sun-protection peaks from the top console. |
| 3. To remove the illumination lamp switch from the panel for access to two screws. To disconnect the socket and to remove the illumination lamp switch. |
| 4. To remove an illumination lamp plafond from the panel for access to the screw. To disconnect the socket and to remove an illumination lamp. |
| 5. By means of the lever to remove the locking plate from the panel, and also to remove the hatch switch from the panel. |
| 6. To unscrew two screws of fastening of the panel, then to lower the panel from a ceiling. |
|
7. By means of the lever to remove the insulator (it is specified by an arrow) from the antenna basis. |
| 8. To unscrew a fastening nut, to disconnect an antenna wire and to remove the antenna from a roof. |
| 9. Installation is made in the sequence, the return to removal. |
|
THE ANTENNA INSTALLED ON THE BACK WING (MODEL THE SEDAN)
| PERFORMANCE ORDER |
| 1. To completely move the antenna. |
| 2. Working in the luggage compartment, to remove finishing on the left side of a luggage carrier. |
|
3. To disconnect antenna (And) and grounding (In) wires from the antenna basis. On models with the electric drive of the antenna to disconnect the electric socket from the antenna drive. |
| 4. To unscrew the lower bolt of fastening of the antenna. |
|
5. In the top part of the antenna to unscrew a round nut, the fixing antenna to the top part of a back wing. |
|
6. To remove a sealing cap. |
| 7. To take the antenna in the luggage compartment. |
| 8. Installation is made in the sequence, the return to removal. |
|
THE ANTENNA INSTALLED ON THE BACK WING (KOMB MODEL)
The antenna is removed as well as on the Sedan cars (see above), but the top end of the antenna is fixed by the condensing ring instead of a round nut.
| PERFORMANCE ORDER |
|
1. To disconnect the electric socket of the drive of the antenna. |
|
2. To unscrew a bolt of fastening of the antenna. |
|
3. At extraction of the antenna it is simple to pass the antenna through the condensing ring down. |
|
|
On the homepage
|
