Peugeot 405
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Fuel system
+ 5. Lubrication systems, coolings
+ 6. System of release
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Steering
+ 11. Suspension brackets
+ 12. Brake system
+ 13. Body
- 14. Electric equipment
14.1. Technical characteristic
14.2. Detection of not closed chain
14.3. Generator
14.4. Starter
14.5. Replacement of switches
14.6. Other electric devices
14.7. Bulbs of external lighting
14.8. Bulbs of internal lighting
14.9. External lighting fixtures
14:10. Adjustment of light of headlights
14:11. Combination of devices
14:12. Elements of a combination of devices
14:13. Hours
14:14. Screen wiper levers
14:15. Engine of a screen wiper and draft
14:16. Engine of a screen wiper of a back door
14:17. Windscreen washers
14:18. Radio receiver
14:19. Loudspeakers
14:20. Antenna
14:21. Anticreeping system
14:22. Safety cushion
14:23. Safety cushion elements
14:24. System of heating and ventilation
+ 14:25. Electrical circuitries and charts
|
Prevention
Before replacement of bulbs of internal lighting to check the corresponding electric chain and a safety lock.
LIGHTING LAMPS OF SALON, WARE BOX AND ILLUMINATION OF THE LUGGAGE CARRIER
| PERFORMANCE ORDER |
|
1. Using the thin screw-driver, to remove a plafond from an illumination lamp. |
|
2. In certain cases for removal of a plafond it is necessary to remove an illumination lamp. |
| 3. For extraction of a bulb to press it, in this situation to turn in any party and to take from the holder. |
| 4. Installation is made in the sequence, the return to removal. |
|
CEILING LAMP
| PERFORMANCE ORDER |
| 1. Using the thin screw-driver, to remove an illumination lamp from the top console on a ceiling. |
|
2. To remove the glow lamp fixed between spring contacts. |
| 3. Installation is made in the sequence, the return to removal. |
|
ILLUMINATION OF THE CONTROL UNIT OF THE HEATER (MODELS TILL 1992)
| PERFORMANCE ORDER |
| For access to glow lamps to remove the control unit of a heater without detachment of cables of management. |
|
ILLUMINATION OF THE CONTROL UNIT OF THE HEATER (MODELS SINCE 1993)
| PERFORMANCE ORDER |
| 1. To remove a negative wire from the accumulator. |
| 2. To remove the central console. |
| 3. To unscrew two screws located at the bottom of an ashtray casing. |
| 4. To remove the radio receiver. |
| 5. To unscrew two screws of fastening from the top part of a frame of the radio receiver. |
| 6. By means of the thin screw-driver to remove a decorative plate from the top corner of a frame of central snuffled systems of ventilation and to unscrew the opened screw. |
| 7. To unscrew four screws of fastening of a slip located under the control panel of heating and ventilation. Two screws are available from a forward part and two of the lower part. |
| 8. For access to the screw of fastening of the dashboard by means of the thin screw-driver to remove the switches located under the central nozzles of system of ventilation and heating. To unscrew the screw. |
| 9. To extend the panel with ventilation nozzles forward, to disconnect an electrical wiring of hours and to remove the panel with ventilation nozzles. |
| 10. To remove handles of management of a heater. |
|
11. To remove the forward panel from the control unit of a heater for access to glow lamps. |
| 12. For extraction of a bulb to press it, in this situation to turn in any party and to take from the holder. |
| 13. Installation is made in the sequence, the return to removal. |
|
LIGHTING LAMP OF HOURS
| PERFORMANCE ORDER |
| 1. For access to the glow lamp of lighting of hours to remove hours. |
|
2. For removal of the glow lamp to turn the boss with a bulb counterclockwise and to take a bulb from hours. |
| 3. Installation is made in the sequence, the return to removal. |
|
LIGHTING LAMPS OF SWITCHES ON THE PANEL
Glow lamps compound with switches cannot be also replaced separately.
ILLUMINATION OF THE COMBINATION OF DEVICES
| PERFORMANCE ORDER |
| 1. To remove a combination of devices. |
|
2. For removal of the glow lamp to turn the boss with a bulb counterclockwise and to take a bulb from a combination of devices, having just pulled it on itself. |
| 3. Installation is made in the sequence, the return to removal. |
|
|
On the homepage
|
