Peugeot 405
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Fuel system
+ 5. Lubrication systems, coolings
+ 6. System of release
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Steering
+ 11. Suspension brackets
+ 12. Brake system
+ 13. Body
- 14. Electric equipment
14.1. Technical characteristic
14.2. Detection of not closed chain
14.3. Generator
14.4. Starter
14.5. Replacement of switches
14.6. Other electric devices
14.7. Bulbs of external lighting
14.8. Bulbs of internal lighting
14.9. External lighting fixtures
14:10. Adjustment of light of headlights
14:11. Combination of devices
14:12. Elements of a combination of devices
14:13. Hours
14:14. Screen wiper levers
14:15. Engine of a screen wiper and draft
14:16. Engine of a screen wiper of a back door
14:17. Windscreen washers
14:18. Radio receiver
14:19. Loudspeakers
14:20. Antenna
14:21. Anticreeping system
14:22. Safety cushion
14:23. Safety cushion elements
14:24. System of heating and ventilation
+ 14:25. Electrical circuitries and charts
|
MULTIPURPOSE SWITCHES OF THE STEERING COLUMN (MODEL TILL 1993)
| PERFORMANCE ORDER |
| 1. To remove casings of a steering column. |
|
2. To unscrew two screws (are specified by shooters) fastenings of the switch to an arm of a steering column. |
| 3. To remove the switch and to disconnect the electric socket. |
| 4. Installation is made in the sequence, the return to removal. |
|
MULTIPURPOSE SWITCHES OF THE STEERING COLUMN (MODEL SINCE 1993)
| PERFORMANCE ORDER |
|
1. Removal of the switch is made similarly earlier stated (see above). Difference consists that access to screws (are specified by an arrow) fastenings of the switch is provided from a forward part of the switch. |
|
2. To remove the multipurpose switch from a steering column. |
|
SWITCHES ON THE DASHBOARD (MODEL TILL 1992)
| PERFORMANCE ORDER |
|
1. Using the thin screw-driver, to release the plastic clamps located on each side the switch and to take the switch from the dashboard. |
| 2. To disconnect the electric socket from the switch. |
| 3. At installation to connect the electric socket to the switch and to press the switch into a nest in the panel before fixing by its clamps. |
|
SWITCHES ON THE DASHBOARD (MODEL SINCE 1993)
| PERFORMANCE ORDER |
| 1. Removal of the switch is made similarly earlier stated (see above) except that plastic clamps are located from above and from below the switch. |
|
2. To remove the switch from the dashboard. |
|
HEATER FAN SWITCH
The switch compound with the control panel of a heater also cannot separately be replaced from the panel.
SWITCHES ON THE CENTRAL CONSOLE
Forward switches
| PERFORMANCE ORDER |
|
1. Using the thin screw-driver, to remove decorative finishing of the basis under the lever of the emergency brake. |
|
2. Using the thin screw-driver, to remove finishing of the switch. |
|
3. Using the thin screw-driver, to remove the switch from the central console and to disconnect the electric socket. |
| 4. Installation is made in the sequence, the return to removal. |
|
Back switches
| PERFORMANCE ORDER |
| 1. Using the thin screw-driver, to remove a back ashtray from the central console. |
|
2. Using the thin screw-driver, to remove finishing of the switch. |
|
3. Using the thin screw-driver, to remove the switch from the central console and to disconnect the electric socket. |
| 4. Installation is made in the sequence, the return to removal. |
|
SWITCHES ON THE DOOR
| PERFORMANCE ORDER |
| 1. By means of the thin screw-driver to take the switch from a nest on a door of the car and to disconnect the electric socket. |
| 2. Installation is made in the sequence, the return to removal. |
|
SWITCHES OF ILLUMINATION OF SALON
The switch on a door rack
| PERFORMANCE ORDER |
|
1. To open a door, then to remove a rubber protective cover (it is specified by an arrow) from the switch. |
| 2. To unscrew the screw of fastening and to take the switch from a door rack. |
| 3. To disconnect the electric socket from the switch and to tie to the switch a thin cord in order that the wire from the switch did not fail in a door rack. |
| 4. Installation is made in the sequence, the return to removal. |
|
The switches installed on a ceiling
Switches compound with lamps cannot be also replaced separately.
Switch of illumination of a luggage carrier (Sedan model)
The switch is located in a suspension bracket and is run by the trunk lid hinge.
| PERFORMANCE ORDER |
| 1. To open a trunk lid. |
|
2. To release brackets and to take the switch from a suspension bracket. |
| 3. To disconnect the electric socket and to remove the switch. |
| 4. Installation is made in the sequence, the return to removal. |
|
Luggage carrier illumination switch (model of Kombi)
Illumination of the luggage compartment is run by the switch sensitive to an inclination and located in a back door.
| PERFORMANCE ORDER |
| 1. To open a back door. |
| 2. To unscrew screws and to remove plastic finishing from an internal part of a back door. |
| 3. Working on perimeter of carpet finishing of a back door, to release brackets of fastening and to remove carpet finishing of a back door. |
|
4. To unscrew the screw (it is specified by an arrow), the fixing switch to a back door. |
| 5. To disconnect the electric socket and to remove the switch. |
| 6. Installation is made in the sequence, the return to removal. |
|
THE HATCH SWITCH WITH THE ELECTRIC DRIVE
| PERFORMANCE ORDER |
|
1. Using the thin screw-driver, to remove the locking plate (close to the hatch switch) from the top console. |
|
2. Through the opening formed after removal of the locking plate to push out the switch and to disconnect the electric socket. |
| 3. Installation is made in the sequence, the return to removal. |
|
|
On the homepage
|
