Peugeot 405
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Fuel system
+ 5. Lubrication systems, coolings
+ 6. System of release
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Steering
+ 11. Suspension brackets
+ 12. Brake system
+ 13. Body
- 14. Electric equipment
14.1. Technical characteristic
14.2. Detection of not closed chain
14.3. Generator
14.4. Starter
14.5. Replacement of switches
14.6. Other electric devices
14.7. Bulbs of external lighting
14.8. Bulbs of internal lighting
14.9. External lighting fixtures
14:10. Adjustment of light of headlights
14:11. Combination of devices
14:12. Elements of a combination of devices
14:13. Hours
14:14. Screen wiper levers
14:15. Engine of a screen wiper and draft
14:16. Engine of a screen wiper of a back door
14:17. Windscreen washers
14:18. Radio receiver
14:19. Loudspeakers
14:20. Antenna
14:21. Anticreeping system
14:22. Safety cushion
14:23. Safety cushion elements
14:24. System of heating and ventilation
+ 14:25. Electrical circuitries and charts
|
The generator (And – Bosch, B – Mitsubishi, C – Valeo)
|
1 –
2 – fan,
3 – forward case,
4 – bearing,
5 – rotor,
|
6 – stator,
7 – holder of brushes regulators,
8 – back case,
9 – vypryamitelny block |
Removal of the generator
|
|
1 – bolt of the tension device of a belt,
2 – fastening bolt,
3 – connections |
Removal
| PERFORMANCE ORDER |
| 1. To disconnect a negative wire from the accumulator. |
| 2. To weaken elements of fastening of the generator to his holders. |
| 3. To weaken the tension device of a maple belt. |
| 4. To take off maple a belt. |
| 5. To disconnect electric connections from the generator. |
| 6. To unscrew bolts of fastening and to remove the generator. |
|
Installation
| PERFORMANCE ORDER |
| 1. To install the generator into place and to screw up fastening bolts not against the stop. |
| 2. To put on maple a belt. |
| 3. To pull a belt before receiving a necessary tension. |
| 4. To screw up fastening elements. |
| 5. To connect electric connections. |
| 6. To connect the accumulator. |
|
Adjustment of a tension of a belt of the generator
| PERFORMANCE ORDER |
| 1. To weaken elements of fastening of the generator. |
| 2. By means of a bolt of the tension device to adjust a belt tension for obtaining necessary value. |
| 3. To screw up elements of fastening and to check adjustment of a tension. |
Prevention
For adjustment of a tension of a belt, first of all, Krikit adaptation (designation Peugeot) is recommended.
|
|
Repair of the generator
Actions for dismantling and assembly of the generator are not difficult.
| PERFORMANCE ORDER |
| 1. During mechanical repair of the generator it is necessary to perform the following operations. |
| 2. To estimate a condition of brushes, degree of their wear, situation, and also pressing contact rings. |
| 3. To estimate a condition of contact rings which should be cleaned only a piece of the material moistened in gasoline or trikhloroetileny and to polish with a thin emery paper; never it is necessary to use an emery cloth. |
| 4. To estimate a condition of bearings which do not demand any actions for their service; bearings are greased for the entire period of operation. |
| 5. To estimate a condition of a rotor and the stator which windings should not have gaps and traces of burn-out. |
Prevention
During check of electric parameters of the generator, and especially the rectifier, the used equipment should not give tension more, than 14 V (it threatens with damage of some elements of the generator).
Vypryamitelny diodes are sensitive to temperature and therefore at their replacement to a ration it is necessary to make quickly and by means of a soldering iron of low power.
|
|
|
On the homepage
|
