| 1. To lift a forward part of the car and to record on supports. |
| 2. To remove forward wheels. |
|
3. To disconnect the electric socket located on the wire going to the sensor of wear of brake shoes. |
| 4. To press the piston into a support, displacing a support aside, opposite piston arrangements. |
| Bendix support |
Prevention
At installation of blocks it is necessary to use a new collar of fixing of a plate of fastening of brake shoes.
|
|
5. Using flat-nose pliers, to remove a small collar of fixing of a plate of fastening of brake shoes. |
|
6. To take a plate of fastening of blocks from a support. |
|
7. To take brake shoes from a support, noting an arrangement of a spring of anti-jingle and to remove a spring from a block. |
|
8. To measure thickness of an overlay of each brake shoe. |
| 9. If the condition of overlays of brake shoes allows their further operation, to clear them, using a pure wire brush and rags. |
| 10. Before installation of blocks to check that the directing fingers freely moved in the holder of a support and to check that rubber protective covers of the directing finger are not damaged. |
| 11. To purify dust and dirt from a support and the piston. |
| 12. To check a condition of dustproof consolidation around the piston. |
| 13. If new brake shoes are established, to press the piston into a support. It can be made a wooden core or the handle of the hammer. At the same time especially to watch that the piston did not warp also the surfaces of the piston and a boot were not damaged. |
| 14. At a piston vdviganiye brake fluid is forced out from the brake cylinder in a broad tank. Therefore constantly to watch liquid level in a tank and if necessary to pump out it. |
| 15. At installation of old brake shoes to put them on the former places. |
|
16. To establish the spring preventing a tinkling sound of brake shoes. |
| 17. To establish brake shoes in a support. |
|
18. At the correct installation of brake shoes if to look at blocks from a forward part of the car, the flute on an internal block has to be above, than a flute on an external block (B – flutes on brake shoes, D – a spring collar, V – the pumping union). |
| 19. To establish a plate of fixing of brake shoes and to record it a spring collar. |
| 20. To connect the socket of the sensor of wear of brake shoes. |
| 21. To check the level of brake fluid in a tank. It should not exceed the marks "max". |
| 22. Several times to press a brake pedal in order that blocks nestled on a disk and repeatedly to check the level of brake fluid in a tank. |
| 23. To perform the same operations on the second forward wheel. |
| 24. To establish wheels and to lower the car. |
| 25. To repeatedly check the level of brake fluid. |
| Girling support |
Prevention
At installation of brake shoes it is necessary to use a new bolt of fastening of the directing finger.
|
|
26. To unscrew a bolt of fastening of the lower directing finger. At the same time for deduction of the directing finger from a provorachivaniye to use a thin wrench. For fastening of the directing finger to use only a new bolt. |
|
27. To turn a support up on the top directing finger and to tie up to a rack with the help of a soft wire. |
| 28. To take brake shoes from the holder of a support. |
| 29. To measure thickness of an overlay of each brake shoe. |
| 30. If the condition of overlays of brake shoes allows their further operation, to clear them, using a pure wire brush and rags. |
| 31. Before installation of blocks to check that the directing fingers freely moved in the holder of a support and to check that rubber protective covers of the directing finger are not damaged. |
| 32. To purify dust and dirt from a support and the piston. |
| 33. To check a condition of dustproof consolidation around the piston. |
| 34. If new brake shoes are established, to press the piston into a support. It can be made a wooden core or the handle of the hammer. At the same time especially to watch that the piston did not warp also the surfaces of the piston and a boot were not damaged. |
| 35. At a piston vdviganiye brake fluid is forced out from the brake cylinder in a broad tank. Therefore constantly to watch liquid level in a tank and if necessary to pump out it. |
| 36. At installation of old brake shoes to put them on the former places. |
|
37. To insert external and internal brake shoes in the holder of a support. |
|
38. To lower a support on brake shoes, passing a wire from the sensor of wear of a brake shoe through a window in a support. |
| 39. To grease a carving of a bolt of fastening of the directing finger with means against unscrewing (Peugeot recommends Loctite Frenetanch). |
| 40. To press a support that it reached the position, then to screw up a bolt of fastening of the directing finger, tightening it the required moment. |
| 41. To connect the electric socket of the sensor of wear of a brake shoe. |
| 42. To check the level of brake fluid in a tank. It should not exceed the marks "max". |
| 43. Several times to press a brake pedal in order that blocks nestled on a disk and repeatedly to check the level of brake fluid in a tank. |
| 44. To perform the same operations on the second forward wheel. |
| 45. To establish wheels and to lower the car. |
| 46. To repeatedly check the level of brake fluid. |
