Peugeot 405

1987-1997 of release

Repair and operation of the car



Peugeot 405
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
   - 3.1. Petrol engines
      3.1.1. Technical characteristic
      - 3.1.2. Repair of the engine
         - 3.1.2.1. The repair which is not demanding removal of the engine
            3.1.2.1.1. Check of a compression
            3.1.2.1.2. Check and adjustment of a gap of valves
            3.1.2.1.3. Driving belt of the camshaft
            3.1.2.1.4. Pulleys of a gear belt
            3.1.2.1.5. Replacement of consolidation of the camshaft
            3.1.2.1.6. Replacement of consolidations of a bent shaft
            3.1.2.1.7. Driving belt of the generator
            3.1.2.1.8. Air filter
            3.1.2.1.9. Cover of a head of the block of cylinders
            3.1.2.1.10. Camshaft
            3.1.2.1.11. Removal and installation of a head of the block of cylinders
            3.1.2.1.12. Dismantling, repair and assembly of a head of the block of cylinders
         + 3.1.2.2. Removal of the engine
         3.1.2.3. Installation of the engine
         3.1.2.4. Dismantling of the engine
         + 3.1.2.5. Assembly of the engine
         3.1.2.6. Start of the engine after capital repairs
   + 3.2. Diesel engines
   + 3.3. Petrol engine 1,4 of dm3
   + 3.4. System of ignition
+ 4. Fuel system
+ 5. Lubrication systems, coolings
+ 6. System of release
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Steering
+ 11. Suspension brackets
+ 12. Brake system
+ 13. Body
+ 14. Electric equipment


e1bd1949



3.1.2.1.7. Driving belt of the generator

Installation of the belt which was in the use

PERFORMANCE ORDER
1. To remove a pulley of a bent shaft.
2. To establish plastic a casing: the lower right, top, lower left.
3. To install adaptation of blocking of a flywheel (Facom D 86) and to tighten a bolt of fastening of a pulley of a bent shaft the moment of 110 Nanometers.
4. To take adaptation of blocking of a flywheel.
5. To establish the lower leaf closing a coupling case.
6. To establish a side casing.
7. To establish a driving belt of the generator and to pull it with effort of 600 N (60 kg) if it new, or with effort of 400 N (40 kg) if it was in the use earlier. It is necessary to use control Krikit adaptation or similar.

Installation of a new belt


PERFORMANCE ORDER
1. To install adaptation of blocking of a flywheel (Facom D 86) and to tighten a bolt of fastening of a pulley of a bent shaft the moment of 110 Nanometers.
2. To take adaptation of blocking of a flywheel.
3. To establish the top casing of a belt.
4. To establish and pull a driving belt of the generator.
5. To start the engine which has to work before turning on of the fan, and then wait until it cools down (at least, two hours at an open cowl).
6. To install the cylinder 1 piston in VMT. The sign on a flywheel has to be opposite to the sign "0" on an adjusting plate of ignition, and the opening for a core in a pulley has to be in the situation corresponding to two hours on the dial of hours.
7. To weaken and tighten nuts of the holder of a tension roller and the clown's lock-nut.
8. To install adaptation of blocking of a flywheel.
9. To take off a driving belt of the generator.
10. To establish plastic a casing: the lower right, top, lower left.
11. To establish a pulley and to tighten bolts the moment of 110 Nanometers.
12. To take adaptation of blocking of a flywheel.
13. To establish the lower leaf closing a coupling case.
14. To establish and pull a driving belt of the generator.
15. To establish a side casing.

On the homepage