Peugeot 405

1987-1997 of release

Repair and operation of the car

Peugeot 405
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Fuel system
+ 5. Lubrication systems, coolings
+ 6. System of release
+ 7. Coupling
- 8. Transmissions
   + 8.1. Mechanical transmission
   - 8.2. Automatic transmission
      8.2.1. Technical characteristic
      8.2.2. Description of the drive
      8.2.3. Removal and installation of the transmission
      8.2.4. Adjustment of management of gear shifting
      8.2.5. Cable of the choice of transfers
      8.2.6. Selector lever
      8.2.7. Cable of compulsory inclusion of a low gear
      8.2.8. Adjustment of a tape of a brake
      8.2.9. Removal and installation of the operating servomotor
      8.2.10. Replacement of a sealing ring of an axis of the selector
      8.2.11. Transmission heat exchanger
+ 9. Power shafts
+ 10. Steering
+ 11. Suspension brackets
+ 12. Brake system
+ 13. Body
+ 14. Electric equipment

8.2.3. Removal and installation of the transmission

GENERAL INFORMATION

The automatic transmission is taken from below the car.

Removal

PERFORMANCE ORDER

1. To remove the accumulator and its holder.

2. To remove the air filter and its arm.

3. To disconnect the electric connections, pipelines and a cable connected to the automatic transmission.

4. To disconnect a cable of management of gear shifting of the automatic transmission about the spherical hinge.

5. From each party of the car to unscrew bolts of fastening of connectors of the stabilizer with suspension bracket levers (the car has to stand on wheels).

6. To place the car on the elevator or to establish a forward part of the car on supports and to remove wheels.

7. To remove both power shafts.

8. To remove the closing leaf of a case of hydrokinetic transfer.

9. To unscrew three bolts of fastening of hydrokinetic transfer to a driving disk (it is necessary to turn gradually a disk so that to get access to the hidden bolts).

10. To unscrew a nut of fastening of a guide of the index of level of oil to the oil pallet.

11. To unscrew three bolts of fastening of a starter, but not to get them.

12. To hook on system of the drive with the automatic transmission on tala so that to unload a metal-rubber element of a support.

13. To separate an axis of a support of system of the drive with the automatic transmission from a metal-rubber element. To remove a metal-rubber element.

14. To establish on the car the special supporting frame (adaptation 0911 A1-AZ) so that to support the engine.

15. As much as possible to lower system of the drive so that the automatic transmission appeared under the car.

16. To unscrew bolts of fastening of the automatic transmission to the engine.

17. To separate the automatic transmission from the engine and to put on the flange (adaptation 0315 A) fixing hydrokinetic transfer.

18. To take the automatic transmission from under the car.

Installation of hydrokinetic transfer in a transmission case

X = 7 mm – a vystupaniye

Installation

PERFORMANCE ORDER

1. It is necessary to perform operations in the return sequence after the relation to removal process, observing the following instructions.

2. Before installation it is necessary to be convinced whether there is an aligning washer of hydrokinetic transfer in cranked to a shaft. This washer should be greased.

3. To check the provision of hydrokinetic transfer (the size X has to make at least 7 mm).

4. To replace everything самоконтрящиеся nuts, elastic linings, consolidations and sealing rings.

5. It is necessary to observe the corresponding moments of tightening of elements of fastening.

6. After installation it is necessary to fill in oil (observing necessary level) in the automatic transmission and to remove air from the cooling system.

7. To adjust management of gear shifting.

On the homepage