Peugeot 405

1987-1997 of release

Repair and operation of the car



Peugeot 405
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
   + 3.1. Petrol engines
   + 3.2. Diesel engines
   - 3.3. Petrol engine 1,4 of dm3
      3.3.1. Technical characteristic
      3.3.2. Check and adjustment of a gap of valves
      3.3.3. Check and adjustment of a corner of an advancing of ignition
      3.3.4. Adjustment of the carburetor
      3.3.5. Removal of the air filter
      3.3.6. Removal of a head of the block of cylinders
      3.3.7. Installation of a head of the block of cylinders
      3.3.8. Removal and installation of the power unit with the petrol engine 1,4 of dm3
      3.3.9. Features of dismantling of the petrol engine 1,4 of dm3
      3.3.10. Dismantling of the TU3 engine
      3.3.11. Dismantling of a head of the block of cylinders
      3.3.12. Assembly of a head of the block of cylinders
      3.3.13. Determination of the size of inserts
      3.3.14. Assembly of the TU3 engine
      3.3.15. Removal of the oil pump
      3.3.16. Dismantling of the oil pump
      3.3.17. Removal of the pump of cooling liquid
      3.3.18. Service and repair of the MA transmission
      3.3.19. Removal and installation of the MA transmission
      3.3.20. Dismantling of the transmission
      3.3.21. Dismantling of a secondary shaft
      3.3.22. Dismantling of a main shaft
      3.3.23. Dismantling of differential
      3.3.24. Dismantling of knot of forks with their axes
      3.3.25. Dismantling of the plug of synchronizers
      3.3.26. Verification of parts of the transmission
      3.3.27. Assembly of the plug of synchronizers
      3.3.28. Assembly of knot of forks with their axes
      3.3.29. Assembly of differential
      3.3.30. Assembly of a main shaft
      3.3.31. Assembly of a secondary shaft
      3.3.32. Assembly of the transmission
   + 3.4. System of ignition
+ 4. Fuel system
+ 5. Lubrication systems, coolings
+ 6. System of release
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Steering
+ 11. Suspension brackets
+ 12. Brake system
+ 13. Body
+ 14. Electric equipment


e1bd1949



3.3.3. Check and adjustment of a corner of an advancing of ignition

GENERAL INFORMATION

System of ignition

the drawing above – the schematic diagram,
the drawing below – the scheme of connections,
1 – accumulator,
2 – ignition coil,
3 – strengthening module,
4 – ignition distributor

Signs for installation of ignition on a flywheel

The corner of an advancing of ignition is checked idling after removal from the distributor of ignition of the vacuum pipeline and closing of the pipeline with a stopper. Signs are visible to check of installation of ignition through an opening in a coupling case (a plate with divisions and a sign on a flywheel). The engine has to be heated-up up to the temperature of normal work.

PERFORMANCE ORDER
1. To connect a stroboscopic lamp to a wire of high voltage of the 1st cylinder according to the instruction of the manufacturer of a lamp.
2. To remove the vacuum pipeline from the vacuum regulator of the distributor of ignition and to close the pipeline a stopper.
3. To start the engine and to check idling turns which have to be equal to 750 rpm.
4. To light with a stroboscopic lamp control signs in an opening of a case of coupling and to read the instrument of size of an advancing of ignition.
5. If this value differs from 8 ° (at 750 rpm of the engine), it is necessary to weaken fastening of the distributor of ignition and to turn it so that the sign on a flywheel was combined with division 8 ° on a plate.
6. To tighten the distributor of ignition and to repeatedly check an ignition advancing corner by means of a stroboscopic lamp.

On the homepage