Peugeot 405

1987-1997 of release

Repair and operation of the car



Peugeot 405
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Fuel system
+ 5. Lubrication systems, coolings
+ 6. System of release
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Steering
+ 11. Suspension brackets
+ 12. Brake system
- 13. Body
   13.1. Care of a body
   13.2. Care of an upholstery and rugs
   13.3. Repair of insignificant damages of a body
   13.4. Repair of strong damages of a body
   13.5. Front bumper
   13.6. Rear bumper
   13.7. Replacement of a headlight and index of turns
   13.8. Replacement of a back lamp
   13.9. Replacement of a forward wing
   13:10. Cowl
   13:11. Cowl lock cable
   13:12. Cowl lock
   13:13. Replacement of the forward panel
   13:14. Doors
   13:15. Door upholstery
   13:16. Lock and handles of opening of a door
   13:17. Glasses of doors
   13:18. Trunk lid (Sedan models)
   13:19. Lock of a trunk lid (Sedan model)
   13:20. Back door (model of Kombi)
   13:21. Lock of a back door (model of Kombi)
   13:22. Central blocking
   13:23. Power windows
   13:24. External rear-view mirrors
   13:25. Front and back flew down
   13:26. Hatch
   13:27. Removable elements of a body
   13:28. Seats
   13:29. Seat belts
   13:30. Finishing of salon
   13:31. Ceiling upholstery
   13:32. Central console
   13:33. Dashboard
+ 14. Electric equipment


e1bd1949



13:16. Lock and handles of opening of a door

INTERNAL HANDLE

Removal

PERFORMANCE ORDER
1. To remove a door upholstery.
2. For access to the handle of opening of a door to remove a protective film from a door.
3. After unscrewing of an element of internal fastening of the handle of a door it is necessary to pull the handle (shooter) back, holding it in the provision of opening (shooter).
4. To take the internal handle of a door by easy movement back (shooter) and simultaneous turn (shooter).
5. To shift assembly of the handle to a forward part of a door, then to take assembly from a door and to disconnect draft.

Installation

Installation is made in the sequence, the return to removal.

EXTERNAL HANDLE OF THE DOOR

Removal

PERFORMANCE ORDER
1. To remove a door upholstery.
2. For access to the handle of opening of a door to remove a protective film from a door.
3. To unscrew a nut (it is specified by an arrow in the drawing at the left) fastenings of the handle.
4. On later models to remove a plastic cover of the handle of opening of a door.
5. To take the handle outside of a door and to disconnect draft of the lock from the handle.

Installation

Installation is made in the sequence, the return to removal.

CYLINDER OF THE LOCK OF THE FORWARD DOOR

The cylinder of the lock can be removed as follows, at the same time removal of an upholstery of a door is optional to receiving access to mechanisms of the lock.

PERFORMANCE ORDER
1. To manufacture two special adaptations, each of which consists of two screws, i.e. the screw with a diameter of 4,2 mm and the 12,7 mm long, soldered to the end screw with a diameter of 8 mm.
2. To open a door and by means of the flat screw-driver to take two plastic caps placed in a back part of a framework of a door.
3. To screw in special devices in fastening bracket paws.
4. To push tools in a door framework for removal of a bracket from the lock cylinder.
5. To convert the lock and to use special tools to fix by a bracket the lock cylinder.
6. To check that the bracket is reliably connected to the lock cylinder, then to unscrew tools from a bracket and to establish two plastic caps.

Removal

PERFORMANCE ORDER
1. To remove a door upholstery.
2. For access to a bracket of fastening of the cylinder of the lock to remove a protective film from a door.
3. Working in a door, to shift a bracket from a back part of the cylinder of the lock.
4. To take the lock cylinder outside of a door.

Installation

Installation is made in the sequence, the return to removal.

DOOR LOCK

Removal

PERFORMANCE ORDER
1. To remove internal and external handles of a door.
2. In a back part of a door to unscrew three screws of fastening of the lock.
3. Where it is applicable, to separate contact of a wire from the engine of the central blocking on assembly of the lock.
4. To lower the lock at a door, to disconnect drafts from the lock and to take the lock from a door.

Installation

Installation is made in the sequence, the return to removal.

On the homepage