Peugeot 405
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Fuel system
+ 5. Lubrication systems, coolings
+ 6. System of release
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Steering
+ 11. Suspension brackets
+ 12. Brake system
- 13. Body
13.1. Care of a body
13.2. Care of an upholstery and rugs
13.3. Repair of insignificant damages of a body
13.4. Repair of strong damages of a body
13.5. Front bumper
13.6. Rear bumper
13.7. Replacement of a headlight and index of turns
13.8. Replacement of a back lamp
13.9. Replacement of a forward wing
13:10. Cowl
13:11. Cowl lock cable
13:12. Cowl lock
13:13. Replacement of the forward panel
13:14. Doors
13:15. Door upholstery
13:16. Lock and handles of opening of a door
13:17. Glasses of doors
13:18. Trunk lid (Sedan models)
13:19. Lock of a trunk lid (Sedan model)
13:20. Back door (model of Kombi)
13:21. Lock of a back door (model of Kombi)
13:22. Central blocking
13:23. Power windows
13:24. External rear-view mirrors
13:25. Front and back flew down
13:26. Hatch
13:27. Removable elements of a body
13:28. Seats
13:29. Seat belts
13:30. Finishing of salon
13:31. Ceiling upholstery
13:32. Central console
13:33. Dashboard
+ 14. Electric equipment
|
MECHANISM OF THE TENSION OF THE SEAT BELT OF THE FRONT SEAT
The system is intended for instant retracting any sagging in a seat belt in case of head-on collision therefore the threat of life to forward passengers decreases. Each front seat can be equipped with the system with the mechanism of a tension of a belt attached directly to the seat belt lock. The mechanism of a tension of a belt is run by the safety cushion control unit. When the system of a tension of a belt works, fuel in the tension mechanism cylinder lights up that the tension mechanism piston therefore sagging of a seat belt is removed forces to move forward. After operation of the mechanism of a tension it is subject to replacement.
Prevention
That the mechanism of a tension did not work when carrying out repair work on the car, it is necessary to disconnect the accumulator and to disconnect the electric socket from the control panel a belt and a safety cushion.
Before performance of any actions on a seat belt to disconnect the negative plug from the accumulator and to wait, at least, for 2 minutes. Further to remove the central panel and to disconnect the socket from the seat belt tension control unit.
Not to subject the tension mechanism to heating it is above 100 °C.
SEAT BELT OF THE FRONT SEAT
Removal
| PERFORMANCE ORDER |
| 1. To remove a covering, then to unscrew the lower bolt of fastening of a seat belt. |
| 2. To remove finishing of the central rack from a ceiling for access to screws of fastening of finishing of the top part of the central rack. |
|
3. To unscrew screws of fastening of finishing of the top part of the central rack. |
|
4. To remove a plate of finishing and to unscrew the top bolt of fastening of a seat belt. |
|
5. To unscrew the fastening screw in the lower part of the top plate of finishing of the central rack and to remove a finishing plate. |
| 6. To unscrew two screws of fastening of the top part of the lower plate of finishing of the central rack. |
|
7. To remove finishing of a threshold, to unscrew screws of fastening of the lower plate of finishing of the central rack and to remove a finishing plate. |
|
8. To unscrew a bolt (it is specified by an arrow) fastenings of an inertial drum and to remove assembly of a seat belt. |
|
Installation
Installation is made in the sequence, the return to removal.
LOCK OF THE SEAT BELT OF THE BELT OF THE FRONT SEAT
The lock of a seat belt is attached by a bolt to a frame of a front seat.
Removal
| PERFORMANCE ORDER |
| If necessary to remove finishing sideways of a seat for access to a bolt. |
|
Installation
| PERFORMANCE ORDER |
| 1. Installation is made in the sequence, the return to removal. |
| 2. To tighten a bolt of fastening of the lock of a seat belt very reliably. |
|
BACK SIDE SEAT BELTS (MODELS SEDAN)
Removal
| PERFORMANCE ORDER |
| 1. To remove a pillow of a back seat. |
| 2. To unscrew a bolt of the lower fastening of a seat belt. |
|
3. To remove the top finishing of a back rack. |
| 4. To remove the finishing of the back panel located before back glass. |
|
5. To unscrew a bolt and to remove an inertial drum. |
| 6. To stretch a belt through a groove in finishing of the back shelf, then to take assembly of a seat belt from the car. |
|
Installation
| PERFORMANCE ORDER |
| 1. Installation is made in the sequence, the return to removal. |
| 2. To tighten a bolt of fastening of the lock of a seat belt very reliably. |
|
BACK SIDE SEAT BELTS (KOMB MODELS)
Removal
| PERFORMANCE ORDER |
| 1. To unscrew a bolt of the lower fastening of a seat belt. |
| 2. To spread out a back seat. |
|
3. Working in the luggage compartment, to unscrew two screws (A) in a forward part of a side decorative slip and a clamp (V) of a seatback. |
|
4. To remove side finishing of a luggage carrier for access to a bolt (V) of fastening of the inertial reel (A). |
| 5. To unscrew a bolt of fastening of an inertial drum and to remove assembly of a drum. |
| 6. To stretch a belt through a groove in finishing of the back shelf, then to take assembly of a seat belt from the car. |
|
Installation
| PERFORMANCE ORDER |
| 1. Installation is made in the sequence, the return to removal. |
| 2. To tighten a bolt of fastening of the lock of a seat belt very reliably. |
|
|
On the homepage
|
